Engine Hanger Covers
Full Coverage 4 Piece Set

A 4 piece set from #8 Mirror Finish stainless steel that are much larger than the Hondaline covers and actually fill all the space between the carbs and your existing side covers from left to right and run from the frame rail on top down to the transmission housing on the bottom.

They are designed to work with KURY tranny covers as well. They really fill up that unfinished area, especially if you have all the other chrome that is available for that area.

They include installation instructions and all required hardware. No need to spend additional money on nuts and bolts! All exposed hardware is matching Stainless Steel.

You are purchasing ALL 4 covers circled in red. Save Time and Money....Get all four pieces at the same time.

NOTE: These covers are designed to work with the stock Honda petcock in the stock location. If you have shimmed the rear of your gas tank (for velocity stacks!!) they may require additional fitting or may not fit at all.

NEW....LOWER PRICE!!

4 Piece Set..................$179.95

Engine Hanger Covers - Hondaline Reproduction

 

A 2 piece set from #8 Mirror Finish Stainless Steel. No rust, No peeling ever. These are copies of the original design...

They are no longer available from Honda.

They are designed to work with KURY tranny covers.

They include all installation instructions and ALL REQUIRED HARDWARE. No need to spend additional money on nuts and bolts!

You are purchasing a set of 2 covers as shown in the photos. They have been meticulously Bead Rolled by hand to replicate the look of the original Hondaline product. Don't be fooled by louvers or slots...these are the first product to re-create the original look.

2 Piece Set............$79.95

Full Coverage Carb End Covers


A 2 piece set from #8 Mirror Finish stainless steel that close off the aft end of each bank of carbs.

These are designed to work with KURY tranny covers as well. They really fill up that unfinished area, especially if you have all the other chrome that is available for that area.

They include installation instructions and all required Hardware. No need to spend additional money on nuts and bolts!

You are purchasing the 2 covers circled in red only...the photos also partially show our Full Coverage Engine Hanger Covers. They are available separately.

2 Piece Set.................$54.95

Engine Hanger Covers
Full Coverage 2 Piece Set

A 2 piece set from #8 Mirror Finish stainless steel that are much larger than the Hondaline covers and actually fill all the space between the carbs and your existing side covers from left to right and run from the frame rail on top down to the transmission housing on the bottom.

They are designed to work with KURY tranny covers as well. They really fill up that unfinished area, especially if you have all the other chrome that is available for that area.

They include installation instructions and all required hardware. No need to spend additional money on nuts and bolts! All exposed hardware is matching Stainless Steel.

You are purchasing the 2 covers circled in red only...the photos also partially show our Carb End Covers.  They are available in a separately.


NOTE: These covers are designed to work with the stock Honda petcock in the stock location. If you have shimmed the rear of your gas tank (for velocity stacks!!) they may require additional fitting or may not fit at all.

2 Piece Set...........$129.95

Stainless Steel Hardware Kit for Honda Valkyrie Engine Hanger Covers

This Is the Same Kit That Is Included With All Our Engine Hanger Covers.

This kit includes all the hardware needed to install new or upgrade your existing Engine Hanger Covers. 

Valkyrie owners have long been plagued by the cumbersome spacer system used on the left hand engine hanger.  This kit uses studs and nuts to replace those spacers and make removal for service a snap. 

All components are Stainless Steel except the single clip nut, which is not exposed to the elements.  Each kit comes complete with all the fasteners required AND our easy to follow, illustrated instruction sheet.

Hardware Kit...............$19.99